R K Engineering Works, VKI Area, Jaipur, repairs crane pendant push-button stations and radio remote controls for EOT, gantry, jib and underslung cranes and electric hoists. We find the fault, repair or replace the transmitter, receiver, push buttons, cable or relays, then test every motion, the emergency stop and all limit switches before handing the crane back.
Request an engineering consultation | Book a site survey | Call +91 9799108009 or +91 9413341806
Who repairs crane pendants and radio remotes in Jaipur?
R K Engineering Works has designed, built and serviced cranes, hoists and goods lifts in Jaipur since 1998. Our works is at 29, Udyog Vihar, Road No. 14, VKI Area, Jaipur 302013, and we are ISO 9001, ISO 14001 and ISO 45001 certified. Because we build crane panels and controls ourselves, our service engineers understand how the pendant or remote talks to the contactors, brakes and limit switches inside the panel.
We attend plants across Jaipur, starting from our own VKI Area works, and plan visits across Rajasthan from the same base. Control repairs can be done as a one-time call or as part of our crane AMC in Jaipur.
What are the common pendant and remote faults?
Most control faults show up as a crane that will not start, a motion that works in one direction only, or a crane that stops for a moment and then carries on. The table below links each symptom to its usual cause and the first safe check.
| Symptom | Likely cause | First safe check | Usual repair |
|---|---|---|---|
| Crane does not respond to the remote | Flat battery, emergency stop pressed, receiver has no supply | Battery, reset the emergency stop, panel supply | Battery or charger, receiver supply fuse, receiver repair |
| One motion dead, others work | Worn push button, broken core in pendant cable, relay fault | Try the same motion from the pendant | Button element, cable core, relay or contactor |
| Crane stops and starts by itself | Weak radio signal, loose plug, cable damaged near the strain relief | Operate closer to the crane, inspect cable at the top | Antenna position, plug, strain relief and cable |
| Emergency stop does not cut power | Stuck or bypassed stop circuit, failed main contactor | Stop using the crane at once | Restore stop circuit, replace contactor, full test |
| Wrong motion runs | Wiring swapped after an earlier repair, wrong pairing | Stop and tag the crane | Correct wiring and labels, re-pair, full test |
| Pendant box cracked or wet | Impact, rain or washing water | Isolate and keep dry | New enclosure, glands and seals |
If the emergency stop does not work or the wrong motion runs, do not use the crane until it is repaired and tested.
Pendant or radio remote: which suits your crane?
| Point | Pendant push-button station | Radio remote control |
|---|---|---|
| Operator position | Walks under or near the load, tied to the cable | Stands at a safe distance with a clear view |
| Wear points | Cable, strain relief, push buttons | Battery, buttons, receiver relays |
| Good for | Short bays, simple duty, back-up control | Long bays, outdoor gantry cranes, hot or dusty areas |
| Common fault | Broken cable cores near the top | Battery and receiver supply |
| Our advice | Keep one as back-up even if you use a remote | Keep a charged spare battery at the crane |
How do we repair a crane pendant or remote? 6 steps
- You call or email with the crane type, capacity, make of control and the fault you see.
- Our engineer isolates the crane, tags it and checks the supply, emergency stop and receiver.
- We trace the fault to the transmitter, receiver, push button, cable, relay or contactor.
- We repair the part or fit a matching replacement, and label any wiring we touch.
- We test every motion in both directions, the emergency stop and all limit switches.
- You get a written service report. After major panel work we can repeat the load test at 125% of rated load.
When should you repair and when should you upgrade?
Repair makes sense when the crane, hoist and panel are in good shape and the fault is in one part. Upgrade makes sense when the same faults keep coming back, spare parts for the old control are hard to get, or the crane needs smoother motion for delicate loads.
| Situation | Repair | Upgrade |
|---|---|---|
| Single failed button, cable or battery | Yes | Not needed |
| Repeated faults in the same panel | Short term only | New control panel and remote |
| Jerky starts swinging the load | Not enough on its own | Add VFD speed control |
| Crane moved from indoor bay to outdoor yard | Check sealing | Radio remote suited to outdoor use |
Read more in our guide to EOT crane modernisation, and see EOT crane spare parts and service for brakes, wheels and hoist parts.
What should operators check every shift?
- Press the emergency stop before work; the crane must not move until it is reset.
- Check the remote battery level and keep the spare on charge.
- Look at the pendant cable for cuts, kinks and a loose strain relief.
- Run each motion briefly without load and check it moves the right way.
- Test the upper hoist limit without load.
- Report any fault at once and tag the crane if it is unsafe.
What details should you send for a faster repair?
| Detail | Why we need it |
|---|---|
| Crane type and capacity | EOT, gantry, jib or underslung; sets the panel layout |
| Make and model of pendant or remote | Tells us which parts to carry |
| Photo of the panel and the remote label | Shows the receiver and wiring before we arrive |
| Fault and when it started | Points to battery, cable, relay or contactor |
| Site address in Jaipur or Rajasthan | Plans the visit from our VKI Area works |
Cranes from R K Engineering Works are designed to IS 3177 and IS 807 where relevant and load-tested at 125% before handover. For new cranes, see our EOT crane manufacturer page for Jaipur.
Frequently asked questions
Who repairs crane pendants and radio remotes in Jaipur?
R K Engineering Works, 29, Udyog Vihar, Road No. 14, VKI Area, Jaipur 302013, repairs pendant push-button stations and radio remote controls on EOT, gantry, jib and underslung cranes and electric hoists, and has built cranes in Jaipur since 1998.
Can you repair a radio remote of another make?
Often yes. We test the transmitter, receiver, relays and wiring. If a part cannot be repaired, we fit a matching receiver and transmitter set and wire it to the existing crane panel.
Is it safe to run the crane on the pendant while the remote is under repair?
Yes, if the pendant, its emergency stop and its cable are healthy and the operator is trained. We check the pendant before handing the crane back on it.
How do you check the crane after a control repair?
We test every motion, the emergency stop, the upper and lower hoist limits and the travel limits, and record the result. After major work we can repeat the load test at 125% of rated load.
जयपुर में क्रेन का पेंडेंट या रेडियो रिमोट कौन ठीक करता है?
आर के इंजीनियरिंग वर्क्स, 29 उद्योग विहार, रोड नंबर 14, वीकेआई एरिया, जयपुर 302013, EOT, गैन्ट्री, जिब और अंडरस्लंग क्रेन व इलेक्ट्रिक होइस्ट के पेंडेंट पुश बटन और रेडियो रिमोट की रिपेयर करता है। कॉल करें +91 9799108009 या +91 9413341806।
रिमोट से क्रेन नहीं चल रही, पहले क्या जांचें?
पहले रिमोट की बैटरी, इमरजेंसी स्टॉप बटन (रीसेट है या नहीं) और पैनल में रिसीवर की बिजली जांचें। फिर भी क्रेन न चले तो उसे पेंडेंट से चलाएं और सर्विस बुलाएं। बिना जांच के रिले या वायरिंग से छेड़छाड़ न करें।
Request an engineering consultation or Book a site survey. R K Engineering Works, 29, Udyog Vihar, Road No. 14, VKI Area, Jaipur 302013. Phone +91 9799108009, +91 9413341806. Email contact@rkengineeringworks.in.
Last updated: 16 Nov 2026
