A helical vs worm gearbox choice comes down to three things: how much speed you need to cut, how much power you can afford to lose as heat, and how the shafts must sit. Helical gearboxes give high efficiency and long life for heavy, continuous duty, while worm gearboxes give a large speed reduction in a small, right-angle body.
This simple guide explains how each type works, where each one fits in a plant, and the points to check before you buy. It is written for plant heads, maintenance engineers and purchase teams who want a gearbox that runs for years without trouble.
What a helical gearbox is
A helical gearbox uses gears with teeth cut at an angle to the shaft. Because the teeth are angled, each tooth meets its partner slowly, from one end to the other. Many teeth share the load at the same time.
This gives a smooth and quiet drive. It also means the gearbox can carry high torque and run for long hours without wearing fast. Helical gearboxes usually have parallel shafts (input and output side by side) or an inline layout. Bevel-helical versions give a right-angle drive.
You will find helical gearboxes in EOT crane hoists and long travel drives, conveyors, mixers, crushers, rolling mills and many other heavy machines.
What a worm gearbox is
A worm gearbox uses a screw-like shaft, called the worm, that turns a toothed wheel, called the worm wheel. The worm and wheel sit at a right angle to each other.
One turn of the worm moves the wheel by only one or a few teeth. So a single stage can give a big speed reduction, such as 10:1 up to 60:1 or more. The body stays compact, which helps when space is tight.
The worm slides against the wheel teeth instead of rolling. This sliding causes more friction and heat. That is the main reason a worm gearbox is less efficient than a helical gearbox.
Worm gearboxes are common in small conveyors, gates, packaging machines, mixers, small winches and many light to medium duty drives.
Helical vs worm gearbox: key differences
The table below puts the main points side by side. The figures are typical ranges for standard industrial units; the exact value depends on the ratio, size and make.
| Point | Helical gearbox | Worm gearbox |
|---|---|---|
| Shaft layout | Parallel or inline (right angle with bevel stage) | Right angle |
| Typical efficiency | High, around 94 to 98% per stage | Lower, around 50 to 90% depending on ratio |
| Ratio per stage | Low to medium, so more stages for big ratios | High ratio in one stage |
| Heat | Low heat at full load | More heat, needs good cooling and oil |
| Noise | Low | Low |
| Size for a high ratio | Larger body | Compact body |
| Shock and heavy duty | Very good | Fair; check service factor |
| Back-driving | Can be back-driven | High-ratio units may resist back-driving, but this is not a safety brake |
| Typical use | Crane hoists, travel drives, heavy conveyors | Light conveyors, gates, packaging, small drives |
Which one should you choose?
Use these simple rules as a starting point.
- Choose a helical gearbox when the machine runs for many hours a day, the motor power is high, or the load has shocks. The energy saved over years is large.
- Choose a helical gearbox for crane hoist and travel drives, where duty class and long life matter.
- Choose a worm gearbox when you need a big reduction in a small space and the duty is light or on-off.
- Choose a worm gearbox when the output must come out at a right angle and the power is small.
- Do not depend on a worm gearbox to hold a hanging load. Always use a proper brake on hoists and lifting drives.
If the choice is close, compare the total cost of ownership, not only the purchase. A helical gearbox wastes less power as heat, so the motor can often be smaller and the electricity use lower.
Points to check before you buy
Give your supplier clear data. It helps them size the gearbox correctly the first time.
- Motor power (kW) and input speed (rpm).
- Required output speed or ratio.
- Output torque and type of load: smooth, medium shock or heavy shock.
- Hours of running per day and number of starts per hour.
- Mounting: foot, flange or shaft-mounted, and shaft position.
- Room temperature, dust and outdoor use.
- Service factor asked for by your plant or the machine maker.
For crane drives, also share the crane duty class. Our guide on EOT crane duty class M3 to M8 explains this in simple words.
Care tips for longer gearbox life
Most gearbox failures come from oil and alignment problems, not from the gears themselves. A few simple habits help a lot.
- Use the oil grade the maker gives and change it on time.
- Check the oil level every month and look for leaks at seals.
- Keep the breather clean so the box does not build up pressure.
- Check coupling alignment after any motor or base work.
- Listen for new noise and feel for extra heat. Both are early warning signs.
- On worm gearboxes, watch the oil temperature closely, as they run warmer.
If an old crane has worn gearboxes, a planned upgrade can fix the problem for good. See our page on EOT crane modernisation for what can be changed.
Gearboxes from R K Engineering Works
R K Engineering Works has designed and built cranes, hoists and lifting equipment in VKI Area, Jaipur since 1998. We make helical and worm gearboxes for industrial drives and for our own crane and hoist systems. The firm is certified to ISO 9001, ISO 14001 and ISO 45001.
See our helical and worm gearbox page for the range, or read our local guides for helical gearbox selection for mills and worm gearbox buyers in Alwar.
FAQs
Is a helical gearbox better than a worm gearbox?
Not always. A helical gearbox is better for high power, long running hours and shock loads because it is more efficient. A worm gearbox is better when you need a large ratio in a small, right-angle body and the duty is light.
Why does a worm gearbox get hot?
The worm slides against the wheel teeth. Sliding causes friction, and friction turns part of the input power into heat. Higher ratios usually run warmer.
Can a worm gearbox hold a load without a brake?
Some high-ratio worm gearboxes resist turning backwards, but this is not reliable. Vibration and wear can let the load slip. Hoists and lifts must always have a proper brake.
Which gearbox is used in an EOT crane?
Most EOT crane hoist and travel drives use helical gearboxes, because they handle heavy duty and long running hours with high efficiency.
What details are needed to select a gearbox?
Share motor kW and rpm, the required output speed, the type of load, running hours per day, starts per hour, mounting style and site conditions.
Talk to an engineer
Not sure which gearbox fits your machine? Send us your motor data and duty, and our team will suggest a suitable helical or worm gearbox. Request an engineering consultation: call +91 9799108009 or +91 9413341806, or email contact@rkengineeringworks.in.
