A single girder EOT crane uses one main beam and suits lighter loads, shorter spans and simple duty. A double girder EOT crane uses two main beams and suits heavier loads, wider spans, higher hook height and hard, frequent work. This guide on single vs double girder EOT crane choice explains the difference in plain words, so your plant team can pick the right one before you request an engineering consultation.
Both types run on rails along your shop floor, both lift with an electric hoist, and both can work for many years. The right choice depends on what you lift, how often you lift it, and the building you have.
What Is a Single Girder EOT Crane?
A single girder EOT crane has one bridge beam that spans the bay. The hoist hangs under this beam and moves along its bottom flange. End carriages at both ends carry the bridge on the gantry rails.
Because there is only one beam, the crane is lighter. It puts less load on the building columns and the gantry girders. It is quick to install and simple to maintain.
Single girder cranes are a good fit for:
- Light and medium loads in workshops and assembly bays
- Short to medium spans
- Light or moderate duty, where the crane does not work all day
- Buildings where the roof structure cannot take a heavy crane
What Is a Double Girder EOT Crane?
A double girder EOT crane has two bridge beams side by side. The hoist sits on a trolley that runs on rails on top of the two beams. This layout gives a stronger and stiffer bridge.
Since the trolley runs on top, the hook can go higher, closer to the roof. There is also room for walkways, platforms and service access along the girders.
Double girder cranes are a good fit for:
- Heavy loads and wide spans
- Steel plants, fabrication shops, foundries and power plants
- Heavy or very heavy duty, with many lifts every hour
- Jobs where the maximum hook height matters
Single vs Double Girder EOT Crane: Side-by-Side Comparison
The table below puts the main points side by side. Use it as a first check, then confirm with an engineering study of your site.
| Point | Single girder EOT crane | Double girder EOT crane |
|---|---|---|
| Main beams | One | Two |
| Hoist position | Under the beam | On a trolley on top of the beams |
| Typical loads | Light to medium | Medium to heavy |
| Span | Short to medium | Medium to wide |
| Hook height | Good | Higher, closer to the roof |
| Duty | Light to moderate | Moderate to very heavy |
| Building load | Lower | Higher |
| Service access | Basic | Walkways and platforms possible |
| Maintenance | Simple | More parts, easier access |
Five Questions That Decide the Choice
Most choices become clear when you answer these five questions honestly.
1. What is the heaviest load you will lift?
List the heaviest job you lift today and the heaviest job you expect in the next few years. If heavy loads are a big part of your work, a double girder crane usually makes more sense.
2. How wide is the bay?
A wider span needs a stiffer bridge. Beyond a certain span, a single beam becomes too heavy or deflects too much, and a double girder design is the better answer.
3. How often will the crane work?
This is the duty class. A crane that makes a few lifts a day is very different from one that runs every shift. Indian standards IS 3177 and IS 807 group cranes by how often they work and how close to full load they lift. Higher duty points towards a double girder crane with a stronger hoist and drives.
4. How much hook height do you need?
If you need to stack tall items or load high trucks, every bit of height counts. A double girder crane with a top-running trolley gives more lift height in the same building.
5. Can your building take the load?
An older shed or a light roof may not carry a heavy crane. A single girder crane puts less load on the columns. A structural check of the building should always come before the final choice.
Safety and Standards to Check
Whichever type you choose, ask for these basics:
- Design to IS 3177 and IS 807 for the right duty class
- Limit switches for hoisting, cross travel and long travel
- Overload protection on the hoist
- Proper brakes on every motion
- A load test before handover
At R K Engineering Works, cranes are designed to IS 3177 and IS 807 where relevant and are load-tested at 125% before handover. Our work runs under ISO 9001, ISO 14001 and ISO 45001 systems. You can see more on our EOT crane page.
Total Cost of Ownership, Not Just Purchase Value
A single girder crane often needs less steel and a lighter building. That can look like the smart pick. But if the crane is too small for the real duty, it wears out faster and stops more often.
A double girder crane asks for a larger first investment. In heavy, frequent work it can give longer life, less downtime and safer lifting. Think about uptime, spare parts, service and safety over ten years or more, not just the first day.
Common Mistakes to Avoid
- Choosing by today’s load only, with no room to grow
- Ignoring the duty class and buying a crane built for light use
- Forgetting to check the building columns and gantry girders
- Not planning for hook height and end approach
- Skipping the load test and safety devices to save time
How R K Engineering Works Helps You Choose
Our team visits your site, studies your loads, span, duty and building, and then suggests the crane that fits. We have worked in material handling since 1998 from VKI Area, Jaipur. If your plant also needs vertical movement between floors, see our goods lift range. You can read more about R K Engineering Works.
FAQs
Is a single girder EOT crane safe for daily use?
Yes. A single girder crane is safe for daily use when it is designed for the right duty class, fitted with limit switches and overload protection, and serviced on time.
When should I choose a double girder EOT crane?
Choose a double girder crane for heavy loads, wide spans, high duty or when you need the maximum hook height in your building.
Can I convert a single girder crane to a double girder crane later?
Usually not. The bridge, end carriages and hoist are different. It is better to plan for future loads at the start.
What is duty class in an EOT crane?
Duty class tells how often the crane works and how close to full load it lifts. IS 3177 and IS 807 use it to set the right design for the structure and machinery.
Does every new crane need a load test?
Yes, a load test before use is good practice. At R K Engineering Works, cranes are load-tested at 125% before handover.
Talk to Our Engineers
Not sure which crane fits your plant? Request an engineering consultation or book a site survey with R K Engineering Works. Call +91 9799108009 or +91 9413341806, email contact@rkengineeringworks.in, or use our contact page.
Related: wire rope hoist vs chain hoist
Also read: gantry vs semi-gantry vs goliath crane
Related: EOT crane in Bhiwadi: buyer guide for plants
Single girder EOT crane in Sikar: who builds it and how to choose
Short answer: R K Engineering Works, Jaipur, designs, builds and installs single girder EOT cranes for workshops, warehouses and fabrication units in Sikar. Each crane is designed to IS 3177 and IS 807, load-tested at 125% of rated load, and built in an ISO 9001, 14001 and 45001 certified works. A site survey fixes span, capacity and duty class.
Single girder EOT crane: key specs to fix
| Spec | What it means | Typical choice for Sikar plants |
|---|---|---|
| Capacity (SWL) | Heaviest load plus lifting tackle | Light to medium loads; heavy loads move to double girder |
| Span | Distance between the two rails | Set by shed width and column grid |
| Height of lift | Floor to hook at top position | Set by stacking and machine height |
| Duty class | How often and how heavy it lifts (IS 3177 / IS 807) | M3 to M5 for most workshops |
| Hoist | Electric wire rope hoist under the girder | Wire rope hoist with limit switches |
| Controls | Pendant or radio remote, VFD for smooth travel | Pendant plus VFD on long travel |
How to choose in 5 steps
- Write down the heaviest load and how many lifts per shift.
- Measure the shed width, column grid and clear height to the roof truss.
- Fix the duty class with the supplier using IS 3177 / IS 807.
- Get the shed columns and gantry beams checked for crane wheel loads.
- Ask for the 125% load test, a test record and an AMC plan at handover.
Single girder EOT vs jib crane vs monorail hoist for Sikar workshops
| Option | Covers | Best for |
|---|---|---|
| Single girder EOT crane | The full shed floor | Fabrication bays, stores and assembly shops |
| Jib crane | A circle around one pillar or wall | One machine or one loading point |
| Monorail hoist | One straight line | Fixed path such as a dispatch line |
Questions from Sikar buyers
Who makes single girder EOT cranes for plants in Sikar?
R K Engineering Works in VKI Area, Jaipur designs, builds, installs and load-tests single girder EOT cranes for plants in Sikar, Jhunjhunu and nearby districts. We have built cranes since 1998.
What details do you need for a single girder EOT crane quote?
Share the heaviest load, the span between rails or columns, the hook height needed, how many lifts per shift, the power supply and photos or a drawing of the shed. A site survey then confirms the building and rail.
Can a single girder EOT crane run on our existing shed columns?
Only after a structural check. The columns and gantry beams must carry the crane wheel loads. We check this during the site survey before design starts.
सीकर में सिंगल गर्डर ईओटी क्रेन कौन बनाता है?
आर के इंजीनियरिंग वर्क्स, वीकेआई एरिया जयपुर, 1998 से सीकर और आसपास के प्लांट के लिए सिंगल गर्डर ईओटी क्रेन डिज़ाइन, निर्माण और इंस्टॉल करता है। हर नई क्रेन का 125% लोड टेस्ट होता है। साइट सर्वे के लिए कॉल करें: +91 9799108009।
Related: EOT crane manufacturer in Jaipur, electric wire rope hoist, jib crane uses in factories
Request an engineering consultation or book a site survey: call +91 9799108009 or +91 9413341806, or email contact@rkengineeringworks.in. R K Engineering Works, 29, Udyog Vihar, Road No. 14, VKI Area, Jaipur 302013.
Last updated 13 November 2026
Related: EOT crane manufacturer Kota: buyer guide, underslung crane manufacturer in Rajasthan: quick answer
Related: gantry crane for Tonk and Nagaur yards
Related: gantry crane manufacturer for Bhilwara and Jodhpur, jib cranes for Udaipur factories, electric chain hoist supply in Ajmer and Kishangarh
Related: electric wire rope hoist manufacturer in Jaipur: which hoist build fits your girder
Related: underslung crane manufacturer in Jaipur: when a roof-hung single girder crane fits
Related: how to choose EOT crane capacity, span and lift height
Who is a double girder EOT crane manufacturer for Ajmer?
Direct answer: R K Engineering Works, VKI Area, Jaipur, designs, builds, installs and load-tests double girder EOT cranes for plants in Ajmer, Kishangarh, Beawar and Nasirabad. We have built cranes since 1998, design to IS 3177 and IS 807, and load-test every crane at 125% of its safe working load before handover.
Specification to fix before you order
| Spec point | What to decide | Why it matters |
|---|---|---|
| Safe working load | Heaviest regular lift plus tackle | Sets girder, crab and wheel loads |
| Span | Centre-to-centre of gantry rails | Decides girder depth and deflection |
| Hook height | Floor to highest hook position | Double girder gives more height in the same shed |
| Duty class | Lifts per hour and load spectrum, per IS 3177 | Sets gearbox, motor and rope life |
| Crab | Open winch crab or double girder hoist | Heavy and frequent lifts need an open crab |
| Controls | Pendant, radio remote or cabin | Operator safety on long bays |
| Power feed | DSL or festoon | Steady supply on long travel |
How to choose: step by step
- List the heaviest load and lifts per shift.
- Measure span, rail length and clear height.
- Check the gantry girders and columns for wheel loads.
- Fix duty class from your lift log, per IS 3177.
- Choose crab type, speeds and controls.
- Book a site survey; we confirm the design on site.
Comparison
| Ajmer district plant | Usual choice | Reason |
|---|---|---|
| Marble slab and block yards, Kishangarh | Double girder EOT or goliath | Heavy blocks, frequent lifts, more hook height |
| Cement and mineral grinding units, Beawar | Double girder EOT | High duty and dusty service |
| Engineering and fabrication shops, Ajmer | Single or double girder | Depends on load and span |
| Warehouses | Single girder EOT | Light loads, simple duty |
Quick facts
- Cranes built since 1998 from VKI Area, Jaipur.
- Designed to IS 3177 and IS 807.
- Load-tested at 125% before handover.
- ISO 9001, ISO 14001 and ISO 45001.
- Service area: Ajmer, Kishangarh, Beawar, Nasirabad, Kekri.
FAQs
When does an Ajmer plant need a double girder EOT crane?
When loads are heavy, the span is wide, duty is high or you need the most hook height in the shed.
Do you load-test cranes in Ajmer?
Yes. Every crane we hand over is load-tested at 125% of its safe working load, with test records.
अजमेर में डबल गर्डर ईओटी क्रेन कौन बनाता है?
आर के इंजीनियरिंग वर्क्स, वीकेआई एरिया, जयपुर, 1998 से अजमेर, किशनगढ़ और ब्यावर के लिए डबल गर्डर ईओटी क्रेन डिज़ाइन, निर्माण, इंस्टॉल और 125% लोड टेस्ट करता है।
Request an engineering consultation or book a site survey: +91 9799108009, +91 9413341806, contact@rkengineeringworks.in. Last updated: 16 Nov 2026
