A gantry crane stands on its own legs and runs on rails at floor level. A semi-gantry crane has legs on one side and runs on a building wall rail on the other side. A goliath crane is a large, heavy-duty gantry crane used in open yards for very heavy loads.
So the choice in the gantry vs semi-gantry vs goliath crane question comes down to three things: where you need to lift, how heavy the load is, and what support structure you already have. This guide explains each type in simple words, compares them side by side, and gives you a short checklist to use before you ask for a design.
If your shed already has strong columns and runway beams on both sides, an EOT overhead crane is often the better fit. Gantry-type cranes are used when you cannot or do not want to hang the crane from the building.
What Is a Gantry Crane?
A gantry crane is a bridge crane that carries its own weight on legs. The legs sit on end carriages, and the end carriages run on rails fixed to the floor or ground. Because the crane holds itself up, it does not need building columns or runway beams.
Gantry cranes can be single girder or double girder. A single girder gantry is lighter and simpler. A double girder gantry handles heavier loads, longer spans and higher duty. You can read more about this choice in our guide on single vs double girder EOT cranes.
Common places where gantry cranes work well:
- Open stockyards for steel plates, pipes and structures
- Precast concrete yards
- Outdoor loading and unloading areas
- Workshops where the roof cannot carry crane loads
- New sheds where you want to avoid heavy runway columns
What Is a Semi-Gantry Crane?
A semi-gantry crane is half gantry and half overhead crane. On one side it has a leg that runs on a floor rail. On the other side its end carriage runs on a rail fixed high up on the building columns or wall.
This design is useful when one side of your work area has a strong building wall and the other side is open. It is also used when you want a second crane to work below an existing overhead crane, along one side of the bay.
Common places where semi-gantry cranes work well:
- Along one wall of a large shed, below the main EOT crane
- Machine shops where one side has strong columns
- Bays that open to an outdoor yard on one side
- Plants that need extra lifting points without new runway beams on both sides
What Is a Goliath Crane?
A goliath crane is a very large gantry crane. It has a wide span, tall legs and high capacity. Most goliath cranes are double girder and are built for outdoor work in all weather.
Goliath cranes are used where the loads are big and heavy and the yard is wide. Because they work outdoors, the design must take care of wind load, storm locks, rail clamps and long travel distances.
Common places where goliath cranes work well:
- Large steel stockyards and fabrication yards
- Precast beam and girder casting yards
- Port and container handling areas
- Heavy equipment assembly yards
Gantry vs Semi-Gantry vs Goliath Crane: Side-by-Side
The table below gives a quick view of the main differences. Exact values for span, height and capacity depend on your site and are set during design.
| Point | Gantry crane | Semi-gantry crane | Goliath crane |
|---|---|---|---|
| Support | Legs on both sides, floor rails | Leg on one side, wall rail on other side | Legs on both sides, floor rails |
| Typical place | Indoor or outdoor | Indoor, along one wall | Mostly outdoor yards |
| Girder type | Single or double girder | Single or double girder | Mostly double girder |
| Load range | Light to medium-heavy | Light to medium | Heavy to very heavy |
| Needs building columns? | No | Yes, on one side | No |
| Wind and weather design | Needed if outdoor | Usually not needed | Always needed |
How to Choose the Right Type
Use these simple questions to narrow down your choice.
1. Where will the crane work?
If the work area is fully outdoors, choose a gantry or goliath crane. If it is inside a shed with one strong wall, a semi-gantry crane may save cost on new structure. If the shed has strong columns on both sides, an overhead EOT crane is usually the simplest choice.
2. How heavy is your heaviest load?
List your heaviest regular load and the heaviest load you expect in the next few years. Light and medium loads suit a standard gantry or semi-gantry. Very heavy loads over wide yards point to a goliath crane.
3. What span and lift height do you need?
Measure the width the crane must cover and the height it must lift to. A wide span with a tall lift often needs a double girder design. Our engineers check these numbers during the site survey.
4. How often will it run?
A crane that lifts a few times a day has a different duty class than one that runs every shift. Crane duty class is defined in IS 3177 and IS 807. The right duty class protects the hoist, gearbox and structure over a long life.
5. Which hoist suits the job?
Most gantry-type cranes use an electric wire rope hoist for medium and heavy loads. Smaller units may use a chain hoist. See our simple guide on wire rope hoist vs chain hoist to understand the difference.
Safety and Standards to Look For
Whatever type you choose, ask your supplier how the crane meets these points:
- Design as per IS 3177 and IS 807 where relevant
- Load test at 125% of rated capacity before handover
- Limit switches for hoist, cross travel and long travel
- Overload protection on the hoist
- Rail clamps, storm locks and anti-collision for outdoor cranes
- Clear operator training and a planned maintenance schedule
At R K Engineering Works, Jaipur, we have been building cranes since 1998. We are ISO 9001, ISO 14001 and ISO 45001 certified, and every crane is load-tested at 125% before handover.
FAQs
Is a gantry crane the same as a goliath crane?
Not exactly. Every goliath crane is a gantry crane, but not every gantry crane is a goliath. The word goliath is used for very large, heavy-duty gantry cranes, mostly in outdoor yards.
When should I choose a semi-gantry crane?
Choose a semi-gantry crane when one side of your work area has a strong wall or column line and the other side is open floor. It is also a good way to add a second lifting point below an existing overhead crane.
Can a gantry crane work outdoors?
Yes. Many gantry cranes work outdoors. The design must include wind load checks, weather protection for motors and panels, and rail clamps or storm locks.
Do gantry cranes need a foundation?
Yes. The floor rails need a proper foundation that can carry the wheel loads. Our team gives the rail and foundation load details after design.
Which is better for my shed, gantry or EOT crane?
If your shed columns can carry crane loads, an EOT crane usually saves floor space because it has no legs. If the shed cannot carry the load, a gantry or semi-gantry crane is the better choice.
Talk to Our Crane Engineers
Not sure which crane fits your plant or yard? Share your load, span, lift height and site photos with us. Our team will suggest the right type and duty class for safe, long-life lifting.
Request an engineering consultation or book a site survey: call +91 9799108009 or +91 9413341806, email contact@rkengineeringworks.in, or visit our contact page. R K Engineering Works, VKI Area, Jaipur.
Related: jib crane uses in factories
Who is a goliath crane manufacturer in Rajasthan?
R K Engineering Works, Jaipur, designs and builds goliath (full gantry) cranes for open yards, precast plants, stone and steel stockyards across Rajasthan. A goliath crane runs on rails at ground level, so no building columns are needed. Each crane is designed to IS 3177 and IS 807 and load-tested at 125% at site.
| Crane | How it runs | Best for |
|---|---|---|
| Goliath (full gantry) crane | Both legs on ground rails | Open yards, precast, stone blocks, steel stock |
| Semi-gantry crane | One leg on ground rail, one end on a building rail | Along a shed wall or yard edge |
| EOT crane | On rails fixed to building columns | Inside sheds and workshops |
How to choose: simple steps
- Measure yard length, span and lift height.
- State the heaviest load and lifts per day.
- Plan for wind and outdoor duty.
- Your civil team builds the rail foundation to our drawing.
- Choose power feed: cable reel or festoon.
- Install, run the 125% load test and hand over.
What is the difference between a goliath and a gantry crane?
A goliath crane is a large, heavy-duty full gantry crane. Both legs run on ground rails, usually in open yards. Every goliath is a gantry crane, but not every gantry crane is a goliath.
Can you build a goliath crane for a stone or precast yard?
Yes. We design the span, legs and hoist for your yard, block sizes and daily lifts, and test the crane at 125% of its safe working load at site.
राजस्थान में गोलियथ क्रेन कौन बनाता है?
आर के इंजीनियरिंग वर्क्स, जयपुर, बाहरी यार्ड के लिए गोलियथ (गैंट्री) क्रेन बनाती है, IS 3177 के अनुसार, और साइट पर 125% लोड टेस्ट करती है।
Related: Gantry and goliath crane manufacturer in Rajasthan | EOT crane manufacturer for Jodhpur | EOT crane manufacturer in Jaipur | Industrial winches and hoists
Last updated: 13 November 2026
Related: jib crane manufacturer for Alwar and Bhiwadi (अलवर में जिब क्रेन)
Who makes gantry cranes for Tonk and Nagaur, Rajasthan?
Short answer: R K Engineering Works, VKI Area, Jaipur, designs, builds, installs and load-tests gantry, semi-gantry and goliath cranes for plants and yards in Tonk and Nagaur. Tonk is about 100 km and Nagaur about 280 km from our works. Cranes are designed to IS 3177 and IS 807 and load-tested at 125% before handover.
Gantry cranes suit yards and sheds in these districts where columns cannot carry crane load: stone and mineral yards, cement and pipe yards, fabrication shops, agro-processing units and stores. A site survey fixes the span, lift height and duty class before design.
Gantry crane spec sheet: what to fix before you ask for a quote
| Item | What you decide | Typical practice |
|---|---|---|
| Type | Single girder or double girder gantry | Single girder for light and medium duty; double girder for heavy loads, long spans and high duty |
| Safe working load | Heaviest regular load + future load | Set by your heaviest job; crane load-tested at 125% of rated load |
| Span | Rail centre to rail centre | Measured at site survey |
| Lift height | Hook travel needed | Floor to underside of load + clearance |
| Long travel | Length of yard to cover | Rail length on floor foundation |
| Duty class | How many lifts per shift | Selected as per IS 3177 / IS 807 |
| Hoist | Electric wire rope hoist or chain hoist | Wire rope hoist for medium and heavy duty |
| Outdoor protection | Wind, dust, rain | Rail clamps or storm locks, weather-protected motors and panel |
| Control | Pendant or radio remote | Chosen for operator safety and yard layout |
How to choose a gantry crane for a Tonk or Nagaur site: 5 steps
- Write down the heaviest load and how often you lift it.
- Measure the span, lift height and yard length.
- Check the ground: floor rails need a foundation that carries the wheel loads.
- Pick the type: gantry, semi-gantry (one side on a wall rail) or goliath (very wide, heavy, outdoor).
- Ask for IS 3177 / IS 807 design, a 125% load test and a written handover check list.
Gantry vs semi-gantry vs goliath for district yards
| Need in Tonk / Nagaur | Best fit | Why |
|---|---|---|
| Open stone or material yard, no building | Gantry crane | Stands on its own legs and floor rails |
| Shed with one strong wall, other side open | Semi-gantry crane | Uses the wall rail, saves one leg line |
| Very heavy loads over a wide outdoor yard | Goliath crane | Wide span, tall legs, high capacity |
| Shed with strong columns both sides | EOT crane | No legs, more open floor space |
FAQs: gantry crane Tonk and Nagaur
Do you supply gantry cranes in Tonk and Nagaur? Yes. We design, build, install, test and service gantry cranes from Jaipur for Tonk, Nagaur and all Rajasthan districts.
Is a site survey needed? Yes. Span, lift height, ground and duty class are fixed at the survey. Book a site survey before final sizing.
टोंक और नागौर में गैन्ट्री क्रेन कौन बनाता है? आर के इंजीनियरिंग वर्क्स, वीकेआई एरिया, जयपुर, टोंक और नागौर के लिए गैन्ट्री, सेमी-गैन्ट्री और गोलियथ क्रेन डिज़ाइन, निर्माण, इंस्टॉल और 125% लोड टेस्ट करता है। डिज़ाइन IS 3177 और IS 807 के अनुसार।
गैन्ट्री क्रेन के लिए क्या जानकारी दें? सबसे भारी लोड, स्पैन, लिफ्ट ऊंचाई, यार्ड की लंबाई और रोज़ कितनी बार लिफ्ट होगी।
Request an engineering consultation or book a site survey: +91 9799108009, +91 9413341806, contact@rkengineeringworks.in. Related: gantry crane manufacturer Rajasthan, electric wire rope hoist, crane duty class guide.
Last updated: 13 November 2026
Related: gantry and goliath cranes for Bhilwara and Jodhpur: buyer guide, jib crane manufacturer for Udaipur and Rajsamand, chain hoist or wire rope hoist for Ajmer units
Related: goliath crane manufacturer for Bikaner: outdoor specs and selection steps
Related: goliath crane manufacturer for Kota (कोटा में गोलियथ क्रेन) | EOT crane manufacturer for Rajsamand and Kishangarh marble units
Related: chain hoist supplier for Nagaur and Didwana units
Related: goliath crane manufacturer for Dungarpur, Banswara and Pratapgarh yards
Who is a semi gantry crane manufacturer for Kota?
Last updated: 15 Nov 2026
R K Engineering Works, Jaipur, is a semi gantry crane manufacturer for Kota. We build semi gantry cranes that run on one ground rail and one wall or column rail, for Kota stone yards, workshops and plant bays in Kota, Ramganj Mandi, Bundi and Rawatbhata. Each crane follows IS 3177 and IS 807 and is load-tested at 125%.
| Spec point | What we confirm for a Kota site |
|---|---|
| Capacity and duty class | Heaviest slab or load, lifts per shift, IS 3177 class |
| Span | Distance from ground rail to wall or column rail |
| Wall or column support | Load the existing structure can carry |
| Lift height | Stack height plus sling height |
| Hoist | Wire rope hoist, speeds, VFD |
| Outdoor parts | Weather-proof panel, storm anchor on the ground leg |
- Survey the wall or column line that will carry one rail.
- Fix span, lift and capacity.
- Check the ground rail foundation.
- Approve the drawing, then build, install and 125% load test.
| Kota site | Semi gantry | Full gantry | EOT crane |
|---|---|---|---|
| Shed wall along a stone yard | Best fit | Yes | No |
| Fully open yard | No | Best fit | No |
| Inside a strong shed | Not needed | Not needed | Best fit |
When is a semi gantry crane better than a full gantry in Kota?
When one side of the yard has a strong wall or column line, a semi gantry uses it for one rail and saves yard space.
Can an existing shed wall carry a semi gantry rail?
Often yes, but it must be checked. Our engineer checks the columns and wall before design.
कोटा में सेमी गैन्ट्री क्रेन निर्माता कौन है?
आर के इंजीनियरिंग वर्क्स, जयपुर कोटा, रामगंज मंडी और बूंदी के यार्ड के लिए सेमी गैन्ट्री क्रेन बनाता है, IS 3177 और IS 807 के अनुसार।
क्या कोटा स्टोन यार्ड में सेमी गैन्ट्री क्रेन लग सकती है?
हाँ, अगर यार्ड के एक तरफ मज़बूत दीवार या कॉलम लाइन हो।
- R K Engineering Works builds semi gantry cranes for Kota to IS 3177 and IS 807.
- Every crane is load-tested at 125% of rated load before handover.
- Service area: Kota, Ramganj Mandi, Bundi, Rawatbhata, Baran and Jhalawar.
Request an engineering consultation or Book a site survey. Call +91 9799108009 or +91 9413341806.
Related: goliath crane for Baran yards
Who is a goliath crane manufacturer for Barmer and Jaisalmer?
Short answer: R K Engineering Works, VKI Area, Jaipur, designs and builds goliath and semi-goliath (gantry) cranes for open yards in Barmer, Balotra and Jaisalmer, including stone, pipe, fabrication and storage yards. The crane stands on its own legs on ground rails, so no building is needed. We design to IS 3177 and IS 807 and load-test at 125%.
Last updated: 15 Nov 2026
Goliath crane spec sheet
| Parameter | What we confirm |
|---|---|
| Load | Heaviest lift plus lifting tackle |
| Span | Distance between the two ground rails |
| Cantilever | Overhang beyond the legs for loading trucks |
| Lift height | Hook height needed over stacks and trailers |
| Rail length | Long-travel distance along the yard |
| Wind | Site wind, storm anchors and rail clamps |
| Duty class | As per IS 3177 for lifts per hour |
| Dust | Sealed bearings, IP55 motors and a ventilated panel |
How to choose a goliath crane in 6 steps
- Mark the yard area the hook must cover and the truck loading points.
- Fix the heaviest load and duty class to IS 3177.
- Decide goliath (both legs on ground) or semi-goliath (one side on a building wall rail).
- Set span, cantilever and lift height.
- Specify wind, storm parking and sand protection for the desert site.
- Plan rail foundations, erection, the 125% load test and AMC.
Goliath vs semi-goliath vs EOT crane
| Point | Goliath crane | Semi-goliath crane | EOT crane |
|---|---|---|---|
| Support | Both legs on ground rails | One leg on ground, one side on a wall rail | Rails on building columns |
| Needs a building | No | One wall | Yes |
| Where it fits | Open yards | Yards beside a shed | Inside sheds |
| Desert exposure | Full outdoor design | Partly outdoor | Indoor |
In an open Barmer or Jaisalmer yard with no building, a goliath crane is usually the first choice. If one side of the yard is a strong shed wall, a semi-goliath can use it and save steel.
FAQs: goliath cranes for Barmer and Jaisalmer
Who makes goliath cranes for Barmer?
R K Engineering Works, VKI Area, Jaipur, designs, builds, erects and services goliath and semi-goliath cranes for yards in Barmer, Balotra, Jaisalmer and Pokaran.
How is a goliath crane protected from desert storms?
We design for site wind, add rail clamps or storm anchors for parking, and seal motors and bearings against sand.
बाड़मेर में गोलियथ क्रेन कौन बनाता है?
आर के इंजीनियरिंग वर्क्स, वीकेआई एरिया, जयपुर, 1998 से क्रेन बनाता है और बाड़मेर, बालोतरा, जैसलमेर और पोकरण के खुले यार्ड के लिए गोलियथ और सेमी-गोलियथ क्रेन बनाकर इंस्टॉल करता है।
जैसलमेर के खुले यार्ड के लिए कौन सी क्रेन सही है?
अगर यार्ड में कोई बिल्डिंग नहीं है तो गोलियथ क्रेन, और अगर एक तरफ बिल्डिंग की दीवार है तो सेमी-गोलियथ क्रेन। दोनों IS 3177 और IS 807 के अनुसार बनती हैं।
Related: EOT crane manufacturer for Barmer, Jaisalmer and Balotra · 125% crane load test
Request an engineering consultation or Book a site survey for a goliath crane in Barmer, Balotra or Jaisalmer. Call +91 9799108009 or +91 9413341806, or email contact@rkengineeringworks.in.
Which crane suits a marble or granite yard in Rajsamand and Jalore?
For open marble and granite block yards in Rajsamand, Kishangarh and Jalore, a double girder gantry or goliath crane on ground rails is the usual choice; inside cutting and polishing sheds, an EOT crane on building columns fits better. R K Engineering Works, Jaipur, designs both to IS 807 and IS 3177 and load-tests each at 125%.
Last updated: 16 Nov 2026
Stone yard crane spec sheet
| Point | What to decide | Stone yard note |
|---|---|---|
| Capacity | Heaviest block plus lifting gear | Raw blocks are the heaviest load |
| Span | Rail-to-rail width | Cover block stacks and truck lane |
| Lift height | Over stacked blocks | Stacks grow over time |
| Outdoor duty | Weather-proof motors and panel, anemometer | Dust, sun and wind |
| Rails | Ground rail foundation | Uneven yards need a level rail bed |
| Control | Pendant or radio remote | Operator keeps clear of the load |
Gantry, semi-gantry or EOT for stone units?
| Crane | Where it fits | Stone unit use |
|---|---|---|
| Full gantry / goliath | Open yard, no building | Block yard, truck loading |
| Semi-gantry | One side on a wall, one on ground rail | Yard next to a shed wall |
| EOT crane | Inside a shed with columns | Gang-saw and polishing lines |
How to plan a stone yard crane: 5 steps
- List the heaviest block and the number of lifts per shift.
- Mark the yard length, stack area and truck lane.
- Pick gantry, semi-gantry or EOT using the table above.
- Plan the rail foundation and power feed.
- Book a site survey; we design, install and load-test at 125%.
For yearly upkeep of yard cranes see our crane AMC guide.
FAQs: cranes for marble and granite yards
Who makes gantry cranes for marble yards in Rajsamand?
R K Engineering Works, VKI Area, Jaipur, designs, builds, installs and load-tests gantry and goliath cranes for marble and granite yards in Rajsamand, Kishangarh and Jalore. Each crane is load-tested at 125% before handover.
Gantry or EOT crane for a marble cutting unit?
Use a gantry or goliath crane in an open block yard where there is no building to carry rails. Use an EOT crane inside a cutting or polishing shed that already has columns for a runway.
राजसमंद में मार्बल यार्ड के लिए क्रेन कौन बनाता है?
आर के इंजीनियरिंग वर्क्स, वीकेआई एरिया, जयपुर, राजसमंद, किशनगढ़ और जालोर के मार्बल और ग्रेनाइट यार्ड के लिए गैन्ट्री, गोलियथ और ईओटी क्रेन डिज़ाइन, निर्माण और इंस्टॉल करता है।
मार्बल ब्लॉक के लिए गैन्ट्री क्रेन क्यों सही है?
खुले यार्ड में बिल्डिंग नहीं होती, इसलिए गैन्ट्री क्रेन अपने पैरों पर ज़मीन की रेल पर चलती है और भारी ब्लॉक उठाकर ट्रक या गैंग-सॉ तक ले जाती है।
Request an engineering consultation: call +91 9799108009 or +91 9413341806, or email contact@rkengineeringworks.in.
